Packaged Heat Pump Type Rooftop Air Conditioner
Model NO.: GT-WKR-35
Mounting: Floor Standing
Lifetime: >20 years
Certification: RoHS, ISO
Condition: New
Product: Air Conditioner
Cooling Capacity: 35kw
Heating Capacity: 37.1kw
Supply Air: 5800
Power: 3n-380V-50Hz
Compressor: Efficient Scroll Closed
Evaporator: Tube Fin Heat Exchanger
Condenser: Tube Fin Heat Exchanger
Refrigerant: R22/R407c
Air Filter: Initially Effect Plate Filter
Trademark: VENTTECH
Transport Package: Export Packaging
Specification: 850kg
Origin: Shanghai, China(Mainland)
HS Code: 8415830000
Model NO.: GT-WKR-35
Mounting: Floor Standing
Lifetime: >20 years
Certification: RoHS, ISO
Condition: New
Product: Air Conditioner
Cooling Capacity: 35kw
Heating Capacity: 37.1kw
Supply Air: 5800
Power: 3n-380V-50Hz
Compressor: Efficient Scroll Closed
Evaporator: Tube Fin Heat Exchanger
Condenser: Tube Fin Heat Exchanger
Refrigerant: R22/R407c
Air Filter: Initially Effect Plate Filter
Trademark: VENTTECH
Transport Package: Export Packaging
Specification: 850kg
Origin: Shanghai, China(Mainland)
HS Code: 8415830000
packaged heat pump type rooftop air conditioner Description:1. Air cooled rooftop air conditioner.
2. Cooling capacity: 8kw to 90kw, a variety of choices.
3. High external pressure.
4. Applicable to residential and commercial buildings, hotels, and scientific research units, factories and enterprises and so on.
packaged heat pump type rooftop air conditioner Features:
1. It is packaged air conditioner which integrates condensing part, evaporating part & control part into a whole unit, firstly promoted & applied in South America, North Europe & Australia.
2. It is air cooled direct evaporation & expansion air conditioner, has no need on cooling water & chilled water system, dispenses with cooling tower/cooling water pump/chilled water pump,  relative pipe work, electric control & terminal equipments, saves user investment.
3. It integrates evaporating part & condensing part into a whole unit which is installed outside to save indoor space, user will only need to install the duct, no need to connect refrigerant pipe work, it works under intellectual control without special care.
Â
Application range:
It is mainly applied to factories, schools, auditoriums, warehouses, etc.
Structure:
1. Panels and frame are made from galvanized steel protected with polyester powder painting to ensure total resistance to atmospheric agents.
2. Direct expansion coils with condensate drain tray.
Hermetic compressor
1. High efficiency scroll compressor for the whole range, with built-in thermal overload cut-out and crankcase heater, mounted on rubber vibration dampers.
2. Ripple type acoustic insulation for compressor section, and thermal insulation for coil and fan section, low noise.
Centrifugal fan
1. Forward curve centrifugal fans for air treatment section and axial fans for condensation section.
2. Front, side and underside air discharge of the treatment unit.
3. High external pressure, long air supply distance.
Electric panel
1. Electric panel consists of breakers and contactors for compressors and fan motors, phase sequence relay and other necessary protection devices for the main components
2. Easy operation line controller
3. Cooling/Heating/Auto
3. Error indication
4. Timing on/off
Optional
1. Economizer with fresh, return air dampers and fresh air hood
2. Free cooling function for low ambient temperature
3. Low ambient control device for operation of outdoor units at ambient temperatures from less than 20C down to -10C
4. BMS devices
4. T3 (Tropical climate)
5. Condenser coil guard
6. Roof curb
7. Metal / aluminum filter
8. Air pressure switch for indoor fan
9. High static condenser fan option with sealed + drain condensing section
10. Optional water heating coil
11. Metal or plastic mesh on condenser coil
12. Optional supply / return air configurations
13. Upgraded evaporator fan motor drives
14. G4 filter, plate and bag filter
Â
|    GT-WKR Series-Roof Top AH Specifiaction 1 | ||||||||||
| Model   GT-WKR- | 10 | 15 | 18 | 20 | 25 | 30 | 35 | |||
| Specification | Cooling capacity 1* | kW | 10.5 | 15 | 18.5 | 21 | 26.3 | 29.8 | 35 | |
| Heating capacity 2* | kW | 11.5 | 15.9 | 19.5 | 22.1 | 27.6 | 32.6 | 37.1 | ||
| Supply air 3* | m3/h | 1800 | 2400 | 2900 | 3500 | 4500 | 5000 | 5800 | ||
| Static pressure 3* | Pa | 100 | 150 | 150 | 180 | 200 | 250 | 250 | ||
| Noise 4* | dB(A) | 60 | 60 | 62 | 62 | 65 | 65 | 68 | ||
| Power | 3N-380V-60Hz | |||||||||
| Total capacity | 3.9 | 5.74 | 7 | 8.27 | 9.96 | 11 | 14.15 | |||
| Color | White | |||||||||
| ooling system | Compressor | Type | Efficient scroll closed | |||||||
| Quantity | 1 | 1 | 1 | 1 | 1 | 1 | 2 | |||
| Supply air fan | Type | Low noise centrifugal type | ||||||||
| Capacity | kW | 0.37 | 0.55 | 0.75 | 0.75 | 1.1 | 1.5 | 2.2 | ||
| Evaporator | Type | Inner grooved copper tube and aluminum fin | ||||||||
| Fin type 5* | Slotted fin hydrophilic aluminum fin | |||||||||
| Condenser | Type | Inner grooved copper tube and aluminum fin | ||||||||
| Fin type 5* | Rippled hydrophilic aluminum fin | |||||||||
| Condenser fan | Type | Low noise axial type | ||||||||
| Quantity | 1 | 1 | 1 | 1 | 1 | 1 | 2 | |||
| Refrigerant | Refrigerant | R22/R407C | ||||||||
| Refrigerant control | External balance type thermal expansion valve | |||||||||
| Air filter | Initially effect plate filter | |||||||||
| Dimensions | L | mm | 1400 | 1400 | 1600 | 1600 | 1850 | 1850 | 2200 | |
| W | mm | 1050 | 1050 | 1200 | 1200 | 1400 | 1400 | 1800 | ||
| H | mm | 1050 | 1050 | 1050 | 1050 | 1200 | 1200 | 1520 | ||
| Weight | kg | 200 | 230 | 260 | 300 | 550 | 600 | 850 | ||
 packaged heat pump type rooftop air conditioner Description:
1. Air cooled rooftop air conditioner.
2. Cooling capacity: 8kw to 90kw, a variety of choices.
3. High external pressure.
4. Applicable to residential and commercial buildings, hotels, and scientific research units, factories and enterprises and so on.
packaged heat pump type rooftop air conditioner Features:
1. It is packaged air conditioner which integrates condensing part, evaporating part & control part into a whole unit, firstly promoted & applied in South America, North Europe & Australia.
2. It is air cooled direct evaporation & expansion air conditioner, has no need on cooling water & chilled water system, dispenses with cooling tower/cooling water pump/chilled water pump,  relative pipe work, electric control & terminal equipments, saves user investment.
3. It integrates evaporating part & condensing part into a whole unit which is installed outside to save indoor space, user will only need to install the duct, no need to connect refrigerant pipe work, it works under intellectual control without special care.
Â
Application range:
It is mainly applied to factories, schools, auditoriums, warehouses, etc.
Structure:
1. Panels and frame are made from galvanized steel protected with polyester powder painting to ensure total resistance to atmospheric agents.
2. Direct expansion coils with condensate drain tray.
Hermetic compressor
1. High efficiency scroll compressor for the whole range, with built-in thermal overload cut-out and crankcase heater, mounted on rubber vibration dampers.
2. Ripple type acoustic insulation for compressor section, and thermal insulation for coil and fan section, low noise.
Centrifugal fan
1. Forward curve centrifugal fans for air treatment section and axial fans for condensation section.
2. Front, side and underside air discharge of the treatment unit.
3. High external pressure, long air supply distance.
Electric panel
1. Electric panel consists of breakers and contactors for compressors and fan motors, phase sequence relay and other necessary protection devices for the main components
2. Easy operation line controller
3. Cooling/Heating/Auto
3. Error indication
4. Timing on/off
Optional
1. Economizer with fresh, return air dampers and fresh air hood
2. Free cooling function for low ambient temperature
3. Low ambient control device for operation of outdoor units at ambient temperatures from less than 20C down to -10C
4. BMS devices
4. T3 (Tropical climate)
5. Condenser coil guard
6. Roof curb
7. Metal / aluminum filter
8. Air pressure switch for indoor fan
9. High static condenser fan option with sealed + drain condensing section
10. Optional water heating coil
11. Metal or plastic mesh on condenser coil
12. Optional supply / return air configurations
13. Upgraded evaporator fan motor drives
14. G4 filter, plate and bag filter
Â
|    GT-WKR Series-Roof Top AH Specifiaction 1 | ||||||||||
| Model   GT-WKR- | 10 | 15 | 18 | 20 | 25 | 30 | 35 | |||
| Specification | Cooling capacity 1* | kW | 10.5 | 15 | 18.5 | 21 | 26.3 | 29.8 | 35 | |
| Heating capacity 2* | kW | 11.5 | 15.9 | 19.5 | 22.1 | 27.6 | 32.6 | 37.1 | ||
| Supply air 3* | m3/h | 1800 | 2400 | 2900 | 3500 | 4500 | 5000 | 5800 | ||
| Static pressure 3* | Pa | 100 | 150 | 150 | 180 | 200 | 250 | 250 | ||
| Noise 4* | dB(A) | 60 | 60 | 62 | 62 | 65 | 65 | 68 | ||
| Power | 3N-380V-60Hz | |||||||||
| Total capacity | 3.9 | 5.74 | 7 | 8.27 | 9.96 | 11 | 14.15 | |||
| Color | White | |||||||||
| ooling system | Compressor | Type | Efficient scroll closed | |||||||
| Quantity | 1 | 1 | 1 | 1 | 1 | 1 | 2 | |||
| Supply air fan | Type | Low noise centrifugal type | ||||||||
| Capacity | kW | 0.37 | 0.55 | 0.75 | 0.75 | 1.1 | 1.5 | 2.2 | ||
| Evaporator | Type | Inner grooved copper tube and aluminum fin | ||||||||
| Fin type 5* | Slotted fin hydrophilic aluminum fin | |||||||||
| Condenser | Type | Inner grooved copper tube and aluminum fin | ||||||||
| Fin type 5* | Rippled hydrophilic aluminum fin | |||||||||
| Condenser fan | Type | Low noise axial type | ||||||||
| Quantity | 1 | 1 | 1 | 1 | 1 | 1 | 2 | |||
| Refrigerant | Refrigerant | R22/R407C | ||||||||
| Refrigerant control | External balance type thermal expansion valve | |||||||||
| Air filter | Initially effect plate filter | |||||||||
| Dimensions | L | mm | 1400 | 1400 | 1600 | 1600 | 1850 | 1850 | 2200 | |
| W | mm | 1050 | 1050 | 1200 | 1200 | 1400 | 1400 | 1800 | ||
| H | mm | 1050 | 1050 | 1050 | 1050 | 1200 | 1200 | 1520 | ||
| Weight | kg | 200 | 230 | 260 | 300 | 550 | 600 | 850 | ||
Â
EDM graphite, also known as graphite block for EDM, is a new type of material, which is now more and more widely used in the precision mold processing industry. At present, in mold processing plants in developed European countries, more than 90% of mold processing electrode materials are graphite. Copper, the once dominant electrode material, has almost lost its advantages compared with graphite electrodes.
Our isostatic graphite and Molded Graphite were tested at the National Electrical Carbon Products Quality Supervision and Inspection Center. The main physical and chemical performance index as follows: the compressive strength--125 mpa, shore hardness -- 65 degrees, resistivity --12 mu Ω m. At the same time, the 10μm,8μm,6μm,4μm products have already began Large-scale production,.and unanimously acknowledged by customers. The 2μm,1μm graphite products are under trial. Our company high quality of isostatic pressing special graphite yield above 90%, far ahead of industry the yield of 70%, the first in the country.
Our isostatic graphite and Molded Graphite were tested at the National Electrical Carbon Products Quality Supervision and Inspection Center. The main physical and chemical performance index as follows: the compressive strength--125 mpa, shore hardness -- 65 degrees, resistivity --12 mu Ω m. At the same time, the 10μm,8μm,6μm,4μm products have already began Large-scale production,.and unanimously acknowledged by customers. The 2μm,1μm graphite products are under trial. Our company high quality of isostatic pressing special graphite yield above 90%, far ahead of industry the yield of 70%, the first in the country.
Company main products:
2.Molded graphite block
3.Graphite rod
4.Graphite tube
5.Graphite plate
7.Graphite crucible
Customized High Pure and density graphite products/graphite block for EDM
Edm Graphite,Graphite Block For Edm,Edm Graphite Electrodes,Isostatic Graphite Column
Henan Carbons New Material Technology Co., Ltd. , https://www.kymoldedgraphite.com